Real Homes is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission. Here’s why you can trust us.

Knowing how to find wall studs is a must for many DIY jobs. If you need to hang a mirror, mount a TV or do anything else wall-related, try one of these 3 simple ways to mark up studs behind plasterboard or masonry walls.

Get the best home decor ideas, DIY advice and project inspiration straight to your inbox!

Thank you for signing up to Realhomes. You will receive a verification email shortly.

There was a problem. Please refresh the page and try again.

One of the first things you need to know when you start DIYing, is how to find studs on a wall. Whether you’re hanging a mirror, a bathroom cabinet, building shelves or doing anything in fact, studs will provide the strongest hold for anything on your walls.

If you live in an older property, it’s likely to be built with more traditional masonry materials and therefore will not have studs on any exterior walls or load-bearing walls. For these, you just need some masonry rawl plugs (opens in new tab) as this too is a super-strong surface to mount things onto. 

Newer properties, however, are mostly timber-framed stud walls internally and dot dab plasterboard on top of blockwork exterior walls. Plasterboard is not strong enough in many cases to hold heavy objects (unless you use some good plasterboard rawl plugs like Grip Its (opens in new tab) ), so finding the studs should be top of your to-do list.

Studs are usually 50mm wide so they may be hard to miss but are typically spaced between 400 and 600mm and run vertically with a few noggins horizontally that run midway up the wall. 

There are three ways you can find a stud:

On the wall you’re planning to mount your TV or hang a mirror, using your knuckle, tap on the wall from one side of the wall to the other, marking with a pencil where the wall sounds dense. Parts of the wall that don’t have a stud will sound hollow, so you should be able to identify what’s a stud and what’s just empty cavity.

Plasterboard is connected to studs with screws, which are then plastered over. Where you find screws, you can bet your bottom dollar that there’s a stud behind it. So, this is a super easy method. Using a strong magnet (opens in new tab) , run it across the wall. If it sticks to a screw, there’s your stud!

A classic, failsafe option. Stud finders are great devices that can detect not only studs, but live wires, steel studs and pipes behind plasterboard. When calibrating, they sense the wall’s density and therefore can tell when the wall is hollow and when there’s something behind it. 

A stud finder will tell you where the edges of the stud are and tell you where the middle is too. 

This is a must-have DIY tool, to use yours, press the power button to the stud setting, then calibrate once it's against the wall. Move it side to side without lifting away from the wall. If you do, you will need to recalibrate, check me out here:

A post shared by Jasmine | DIY for Beginners (@_ohabode) (opens in new tab)

A photo posted by on

Once you have your studs marked out, you can go ahead and drive screws straight in – no plugs needed. It’s a super strong hold, after all, they’re holding up your house!

 Jasmine Gurney is a DIY pro, inspiring women with power tools via her home improvement blog Oh Abode and on Realhomes.com.

We test the Canon SELPHY Square QX10 to see how it can help immortalise those most treasured memories

By Caroline Preece • Published 21 July 22

Our comprehensive editor-approved list of the best places to shop for bedding for all needs and price points

By Jaclyn Turner • Published 21 July 22

Real Homes is part of Future plc, an international media group and leading digital publisher. Visit our corporate site. © Future Publishing Limited Quay House, The Ambury, Bath BA1 1UA. All rights reserved. England and Wales company registration number 2008885.